Retour aux applicationsSoumettre
OpenThreadBorderRouter-HA

OpenThreadBorderRouter-HA

Application Docker from pureelectricity's Repository

Vue d'ensemble

OpenThread Border Router (Home Assistant Optimized) This container runs an OpenThread Border Router (OTBR) specifically tweaked for integration with Home Assistant via the Silicon Labs EFR32MG21 chipset (SkyConnect, ZBT-1, Sonoff ZBDongle-E). CRITICAL PREREQUISITES - READ BEFORE INSTALLING: 1. Enable IPv6 in Unraid: Navigate to Settings > Network Settings. Ensure "Network Protocol" is set to IPv4 + IPv6. If this is disabled, Thread networking will not function. 2. Host Kernel Configuration (Persistence Required): Unraid resets network forwarding rules on every reboot. You must apply the following commands on the Unraid Host to prevent the Thread network from breaking. Commands to run: [code] sysctl -w net.ipv6.conf.all.forwarding=1 sysctl -w net.ipv6.conf.br0.accept_ra=2 sysctl -w net.ipv6.conf.eth0.accept_ra=2 [/code] How to automate this (Choose one): Option A: User Scripts Plugin (Recommended) Install the "User Scripts" plugin. Create a new script with the commands above and set it to run "At Startup of Array". Option B: The Go File (Native) Edit the file /boot/config/go on your flash drive and add the commands to the bottom of the file. This will execute them during the boot sequence. 3. USB Firmware: Your USB stick MUST be flashed with OpenThread RCP Firmware at 460800 baud. (Multiprotocol firmware is not supported). Configuration Notes: - Network Type: Must be Host for mDNS discovery. - WebUI Port: Default is 8099 (to avoid conflict with Unraid Port 80).

Arguments d'exécution

Interface utilisateur Web
http://[IP]:[PORT:8099]/
Réseau
host
Coquille
bash
Privilégié
true
Paramètres supplémentaires
--cap-add=SYS_ADMIN --cap-add=NET_ADMIN --sysctl "net.ipv6.conf.all.disable_ipv6=0" --sysctl "net.ipv4.conf.all.forwarding=1" --sysctl "net.ipv6.conf.all.forwarding=1"

Configuration du modèle

Radio Device (Passthrough)Devicerw

Map your physical USB stick here (use /dev/serial/by-id/...). It maps to /dev/ttyUSB0 inside the container.

Cible
/dev/ttyUSB0
Défaut
/dev/serial/by-id/YOUR_DEVICE_HERE
Radio Path (Internal)Variable

The internal path to the radio. Leave this as /dev/ttyUSB0 matching the internal side of the device mapping above.

Cible
DEVICE
Défaut
/dev/ttyUSB0
Valeur
/dev/ttyUSB0
BaudrateVariable

Baudrate for RCP Firmware. SkyConnect/ZBT-1/Sonoff-E usually use 460800.

Cible
BAUDRATE
Défaut
460800
Valeur
460800
Flow ControlVariable

Hardware Flow Control. Set to 1 for SkyConnect/ZBT-1. Set to 0 if using a generic stick without flow control support.

Cible
FLOW_CONTROL
Défaut
1
Valeur
1
Backbone InterfaceVariable

The Unraid Host interface connected to your LAN/Internet. Usually br0 or eth0.

Cible
BACKBONE_IF
Défaut
br0
Valeur
br0
OTBR WebUI PortVariable

Port for the OTBR Web Interface. Changed from default 80 to prevent conflict with Unraid.

Cible
OTBR_WEB_PORT
Défaut
8099
Valeur
8099
OTBR REST PortVariable

Port for the REST API (Used by Home Assistant).

Cible
OTBR_REST_PORT
Défaut
8081
Valeur
8081
Enable NAT64Variable

Enable NAT64 translation.

Cible
NAT64
Défaut
1
Valeur
1
Enable FirewallVariable

Enable internal firewall.

Cible
FIREWALL
Défaut
1
Valeur
1
Data StoragePathrw

Persistent storage for Thread credentials and dataset.

Cible
/data/thread
Défaut
/mnt/user/appdata/otbr
TUN AdapterDevicerw

Required for creating the wpan0 network interface.

Cible
/dev/net/tun
Défaut
/dev/net/tun
Valeur
/dev/net/tun
Local TimePathro

Sync time with host.

Cible
/etc/localtime
Défaut
/etc/localtime
Valeur
/etc/localtime
Auto-Flash FirmwareVariable

Disable automatic firmware flashing attempts.

Cible
AUTOFLASH_FIRMWARE
Défaut
0
Valeur
0
Log LevelVariable

Log verbosity (info, debug, warn).

Cible
OTBR_LOG_LEVEL
Défaut
info
Valeur
info

Catégories

Home AutomationTools > Utilities

Liens

ModèleSoutienRegistreProprojet

Détails

Référentiel
ghcr.io/ownbee/hass-otbr-docker:latest
Registre
https://github.com/ownbee/hass-otbr-docker
Dernière mise à jour2026-05-31
Première vue2025-12-15

Exécutez OpenThreadBorderRouter-HA sur Unraid.

OpenThreadBorderRouter-HA est listé dans Community Apps pour Unraid OS. Explorez Unraid pour créer un serveur domestique flexible, un NAS ou un laboratoire domestique.

Explorez Unraid OS